Extreme Flight 110" Yak54 - GP-123

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Extreme Flight 110" Yak54 - GP-123

Postby Joe Hunt » Wed Aug 10, 2016 1:38 am

I'm going to add a slot closer to the servo... like I did here on my Pilot RC 122" Extra.
Attachments
20160809_095659.jpg
To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Extreme Flight 110" Yak54 - GP-123

Postby Joe Hunt » Sun Aug 14, 2016 12:02 pm

Okay, I got out to the garage for a couple of more hours...

I finished all the hinging (all I had left was the rudder) and it's really nice. :)

I decided it was time to put it on the gear... so I put together the stock tailwheel. If you want to make a flat spot for the set screw to tighten on you have to be accurate as it will impact the wheel alignment. Also, I found two of the three collars and set screws unusable. I tried, because a collar is a collar to me. But, no dice. So, I broke out some DUBRO collars and used them to hold on the wheel.
Attachments
20160813_203629.jpg
To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Extreme Flight 110" Yak54 - GP-123

Postby Joe Hunt » Sun Aug 14, 2016 12:03 pm

I was looking at the tiller arm setup and thinking this would only work if you drill a hole big enough for the balljoint to be glued into the bottom of the rudder. I checked the manual for the first time and that is what it says to do. haha So I did. :)
To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Extreme Flight 110" Yak54 - GP-123

Postby Joe Hunt » Sun Aug 14, 2016 12:23 pm

Putting on the landing gear was a bit tricky. I put the bolts in from the top and to keep the washers on and the bolts on the ball driver I lathered them up with RTV. Then I put the fuse on its side and threadlocked on the lock nuts.
Attachments
20160813_211303.jpg
To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Extreme Flight 110" Yak54 - GP-123

Postby Joe Hunt » Sun Aug 14, 2016 12:24 pm

Finally on the gear!
Attachments
20160813_212751.jpg
To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Extreme Flight 110" Yak54 - GP-123

Postby Joe Hunt » Mon Aug 15, 2016 1:51 am

I put the axles, tires, and spats on today. I went ahead and gave the stock axles a try. But, not the stock axle collars. Two of the collars were missing and the other two were pretty poorly tapped and threaded. I couldn't get them to work. So, I used the stock axles with DUBRO collars. The stock tires looked good, too. But, I went ahead and put some 4" DUBRO treadlites on, although I plan on going to 4-1/2" soon.

I painted the inside of the spat silver, because it looked unfinished. I also got some graphics on that I got from www.p1hobbies.com.
Attachments
20160814_194035.jpg
20160814_191950.jpg
20160814_191933aaa.jpg
20160814_183911.jpg
To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Extreme Flight 110" Yak54 - GP-123

Postby Joe Hunt » Wed Aug 31, 2016 12:20 pm

Again, I flew a Mike Domo's V2 and loved it... so I got this one. I would have tried the stock hinges (adding one to each end of each surface) but when I saw Jeff Leshinsky's similar looking china round hinges all fail totally in less than 30 flights on his other brand ARF I got paranoid. haha

I am going to give it a try even though these piano wire jobs usually bend and fail pretty quickly. I did have trouble with two of the collars and set screws. And, then there were two missing for the main gear axles... so I've replaced them all with DUBRO collars.

When I use the DUBRO collars I like to use 1/8" 6/32 bolts... much nicer to snug up than a setscrew.
Attachments
20160814_161719.jpg
20160814_162259.jpg
To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Extreme Flight 110" Yak54 - GP-123

Postby Joe Hunt » Wed Aug 31, 2016 12:23 pm

2am hinging video, for anyone interested, or bored. haha

To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Extreme Flight 110" Yak54 - GP-123

Postby Joe Hunt » Wed Aug 31, 2016 12:26 pm

I can't understand how the ARF manufacturer's are still putting the control horn trusses so close together. They should be wide enough to put a conical on each side of the ball joint.

I stuffed 3 small washers in on the binding side so that I could use the 1-3/4" hole on the servo arm. 2" would require a constant bind on the ball joint. You can't use most normal size washers, either. They just exacerbate the problem. These smallish diameter black washers work.

Better setup would be to cut a new slot further away to make room for conicals. Another option is to just drill for and install a bolt. Which I usually end up doing.
Attachments
20160817_222026.jpg
20160817_224747.jpg
To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Extreme Flight 110" Yak54 - GP-123

Postby Joe Hunt » Wed Aug 31, 2016 12:27 pm

Here's how I fixed this problem on my 122" Extra:
Attachments
20160808_175519.jpg
To support this site, the reviews, and the photoshoots:


Return to “Build Threads”

Who is online

Users browsing this forum: No registered users and 6 guests