AeroWorks 50cc Yak 55

User avatar
cherrybomb48
Posts: 26
Joined: Fri Aug 28, 2015 4:33 pm

AeroWorks 50cc Yak 55

Postby cherrybomb48 » Mon Oct 12, 2015 2:20 pm

Alright! I finally got a chance to post it on this site!

Setup:

DLE 61 with stock muffler
AR9110 Powersafe RX
Power HD Storm 3's for the surfaces
Power HD Coreless D15 HV for throttle
2x Pulse 2550 mAh 7.4v lipos
Tech Aero IBEC
24oz Extreme Flight tank
Blue Miracle Spinner
24x10 carbon prop
1 1/2" arms on ail, elev. 4" on rudder

So this plane is really nice! Initial inspection of the airframe come out mostly good. Seem someone was rough with the box during shipping and broke a stringer along the bottom of the fuselage. A couple minutes of epoxy and heat gun got it fixed right up.
IMG_0811.JPG

IMG_0812.JPG

IMG_0813.JPG

IMG_0814.JPG

IMG_0815.JPG

IMG_0816.JPG


When I started the build I didn't have all my equipment so I put off the wings and stabs for a while. Straight to the fuselage I went! Did the rudder install just like the manual said and it seems to be holding fine. Got plenty of travel in both directions.
IMG_0817.JPG

IMG_0818.JPG

IMG_0819.JPG

IMG_0820.JPG

IMG_0821.JPG


I also installed the landing gear and wheel pants.
IMG_0822.JPG

IMG_0823.JPG

And before I left for the weekend I mounted the engine.
IMG_0824.JPG
Attachments
IMG_0800.JPG
Geaux Lower! :mrgreen:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: AeroWorks 50cc Yak 55

Postby Joe Hunt » Mon Oct 12, 2015 2:27 pm

Great pics! I love how macho these AW Yak55s look! Totally thug! haha And, I love the scheme, can't go wrong with red, white, and blue!

TFPU and keep at it!
To support this site, the reviews, and the photoshoots:

User avatar
cherrybomb48
Posts: 26
Joined: Fri Aug 28, 2015 4:33 pm

Re: AeroWorks 50cc Yak 55

Postby cherrybomb48 » Mon Oct 12, 2015 2:32 pm

This past weekend I was able to make it home and do a good bit more on the Yak.
All my gear showed up too.
IMG_0838.JPG


First thing I did was to put some Viton line in the tank. Its not that I don't trust the included blue line, but I bought the Viton so I don't have to trust the blue line! :D
IMG_0839.JPG


First up was the Pull-Pull! I did my best to get perfect geometry in my lines, but it didn't work out :( . No biggie
It actually seems to be my best setup yet. The included hardware is nice and set right into place.
IMG_0840.JPG

IMG_0841.JPG


These Power HD's seem to be decent servos. I picked them up a good price when I was flying for Redwing RC alittle over a year ago. I haven't run the on 7.4v yet though.
IMG_0842.JPG

IMG_0843.JPG

IMG_0844.JPG
Geaux Lower! :mrgreen:

User avatar
cherrybomb48
Posts: 26
Joined: Fri Aug 28, 2015 4:33 pm

Re: AeroWorks 50cc Yak 55

Postby cherrybomb48 » Mon Oct 12, 2015 2:43 pm

Throttle time!

So on this Yak, I decided to take my time and try to put the servo in the perfect location so I don't have to destroy the firewall to get the linage through. I usually rush and wind up messing up the placement.
However, this time it went very smooth! Placed the servo at a good spot on the wall and drilled my hole perfectly. :D

IMG_0846.JPG

IMG_0847.JPG

IMG_0848.JPG

IMG_0845.JPG

IMG_0851.JPG


I put a few servo screws into the throttle mount just in case the epoxy decides to break loose.
IMG_0849.JPG


I really like the custom fitted throttle arm too!
IMG_0850.JPG


Setting the choke rod was uneventful
IMG_0852.JPG


And mounted the ignition on the right side of the firewall.
IMG_0853.JPG
Geaux Lower! :mrgreen:

User avatar
cherrybomb48
Posts: 26
Joined: Fri Aug 28, 2015 4:33 pm

Re: AeroWorks 50cc Yak 55

Postby cherrybomb48 » Mon Oct 12, 2015 2:53 pm

Fuel system install:
First up was cutting the fuel dot hole. These fuel dots included with the airframe are nice!
IMG_0854.JPG


My tygon just so happens to be the right size that makes the fuel cap fit snuggly when retracted.
IMG_0857.JPG


I dropped my tank in there and used Velcro straps to keep it in place.
IMG_0856.JPG

I also mounted my IBEC and vent hole at the bottom of the plane. I just don't have pictures for them yet. :o

Next up was cutting the cowl. This cowl is extremely nice! Very well painted! I didn't want to cut it lol
I opened some vent space on the bottom of the scoop. I will see if I need to open more up later.
IMG_0858.JPG

IMG_0859.JPG

IMG_0860.JPG

IMG_0861.JPG

IMG_0862.JPG


Next time Im home I will do some more building and picture taking.
Geaux Lower! :mrgreen:

User avatar
cherrybomb48
Posts: 26
Joined: Fri Aug 28, 2015 4:33 pm

Re: AeroWorks 50cc Yak 55

Postby cherrybomb48 » Mon Oct 12, 2015 2:55 pm

Geaux Lower! :mrgreen:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: AeroWorks 50cc Yak 55

Postby Joe Hunt » Mon Oct 12, 2015 3:26 pm

To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: AeroWorks 50cc Yak 55

Postby Joe Hunt » Mon Oct 12, 2015 3:28 pm

To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: AeroWorks 50cc Yak 55

Postby Joe Hunt » Mon Oct 12, 2015 3:31 pm

To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: AeroWorks 50cc Yak 55

Postby Joe Hunt » Mon Oct 12, 2015 3:34 pm

To support this site, the reviews, and the photoshoots:


Return to “Build Threads”

Who is online

Users browsing this forum: No registered users and 0 guests